O ring manufacturer and supplier in China: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Find extra info on hydraulic seal suppliers.
Mechanical seals often need to be used in chemical applications. When confronted with some harsh chemicals, mechanical seals containing elastomers made of Viton, Kalrez or Chemrez can’t hold up. Because PTFE (polytetrafluoroethylene)or as most people know it Teflon ® , has a 0-14 ph range it usually will hold up. Like most materials every choice has an up and a down side. Because PTFE will handle most chemical applications, chemical attack is no longer an issue. One the down side PTFE wedges can cause fretting of your sleeve or shaft if you have not hard surfaced your shaft or sleeve (plasma coating). The stationary element of your seal will require a PTFE gasket. It’s not much good to have a PTFE on the rotary and then use an elastomer on the seat. We have seen it done, and because it is a static application some have gotten away with it, but it is not recommended. Most commonly the seat will be a L-shaped or Clamped mount style to allow space for a PTFE gasket to be used as the secondary sealing element.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
The O-ring seal, which is also called shaft seal, is noted for a reasonable compression and stretch rate to achieve a good sealing effect. It will not leak when it is sealed statically. At the same time, the O-ring size is properly matched to the groove size. The structure is simple and its installation is very close to the machine. Its most prominent advantage is its self-sealing effect, eliminating the need for periodic adjustments. We guarantee that the size and mounting grooves of all our O-rings are standardized, so they are cost-effective and easy to maintain. They have low frictional resistance and are suitable for occasions where the pressure is often alternating.
Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.
Wiper seals are utilized to remove contaminants like moisture, soil, and dust. Some wipers or even scrapers possess a secondary lip utilized to catch any oil which might have bypassed the major seal. The secondary lip can also get rid of any bonded contaminate in the pole surface. These kinds of wipers are usually called double-edged wipers. Metallic scrapers could be used for sub zero temperature software and especially arduous software where foreign substances can deposit the pole.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Find extra info at https://www.dmsseals.com/.
DMS Seals is a professional mechanical seals manufacturer and oil seal supplier for hydraulic seals, O-Rings, spring energized seals, oil seals, mechanical seal and so on. Hydraulic seals including step seals, glyd rings, guide strips, wiper seals, rod seals, piston seals, rotary seals, wear rings. We can provide the hydraulic seals with bronze filled PTFE, carbon filled PTFE, graphite filled PTFE, MoS2 filled PTFE, glass filled PTFE, virgin PTFE. About O-Rings, we can supply NBR, FKM, silicone, EPDM, HNBR, ACM, FFKM material.